感應自動門是現代建筑中常見的門禁設備，它可以通過感應器自動開啟和關閉，方便人們的進出。然而，隨著使用時間的增長，感應自動門也會出現各種故障，需要及時維修。濟南感應門廠家將介紹感應自動門的常見故障及維修方法，幫助大家問題。

Inductive automatic doors are common access control devices in modern architecture, which can automatically open and close through sensors, facilitating people's entry and exit. However, as the usage time increases, various faults may also occur in the induction automatic door, requiring timely repair. Jinan sensor door manufacturer will introduce common faults and maintenance methods of sensor automatic doors to help everyone solve problems.

一、常見故障

1、 Common faults

1.感應器失靈：感應器是感應自動門的核心部件，如果失靈，門就無法自動開啟和關閉。感應器失靈的原因可能是感應器本身故障、感應器與控制器之間的連接線路故障或者控制器故障。

1. Sensor failure: The sensor is the core component of the sensing automatic door. If it fails, the door cannot automatically open and close. The cause of sensor failure may be a malfunction of the sensor itself, a faulty connection line between the sensor and the controller, or a malfunction of the controller.

2.門扇無法關閉：感應自動門在關閉時，門扇無法完全關閉或者關閉后又自動打開，這可能是門扇與地面或者門框之間的間隙過大，或者門扇的調整螺絲松動。

2. Door leaf cannot be closed: When the induction automatic door is closed, the door leaf cannot be fully closed or automatically opened after closing, which may be due to excessive clearance between the door leaf and the ground or door frame, or loose adjustment screws of the door leaf.

3.門扇無法打開：感應自動門在開啟時，門扇無法打開或者打開后又自動關閉，這可能是門扇與地面或者門框之間的摩擦力過大，或者門扇的調整螺絲松動。

3. Door leaf cannot be opened: When the induction automatic door is opened, the door leaf cannot be opened or automatically closes after opening. This may be due to excessive friction between the door leaf and the ground or door frame, or the adjustment screws of the door leaf are loose.

二、維修方法

2、 Maintenance methods

1.感應器失靈：檢查感應器本身是否故障，如果故障需要更換感應器。如果感應器正常，檢查感應器與控制器之間的連接線路是否松動或者損壞，如果有需要重新連接或者更換連接線路。如果連接線路正常，檢查控制器是否故障，如果故障需要更換控制器。

1. Sensor malfunction: First, check if the sensor itself is faulty. If it fails, replace the sensor. If the sensor is normal, check if the connection line between the sensor and the controller is loose or damaged. If necessary, reconnect or replace the connection line. If the connection line is normal, check if the controller is faulty. If it is faulty, replace the controller.

2.門扇無法關閉：檢查門扇與地面或者門框之間的間隙是否過大，如果過大需要調整門扇的位置。如果門扇位置正常，檢查門扇的調整螺絲是否松動，如果松動需要重新調整螺絲。

2. Door leaf cannot be closed: First, check if the gap between the door leaf and the ground or door frame is too large. If it is too large, adjust the position of the door leaf. If the position of the door leaf is normal, check if the adjustment screws of the door leaf are loose. If they are loose, readjust the screws.

3.門扇無法打開：檢查門扇與地面或者門框之間的摩擦力是否過大，如果過大需要調整門扇的位置。如果門扇位置正常，檢查門扇的調整螺絲是否松動，如果松動需要重新調整螺絲。

3. Door leaf cannot be opened: First, check if the friction between the door leaf and the ground or door frame is too large. If it is too large, adjust the position of the door leaf. If the position of the door leaf is normal, check if the adjustment screws of the door leaf are loose. If they are loose, readjust the screws.

三、注意事項

3、 Precautions

1.在維修感應自動門時，需要先關閉門的電源，以免發生電擊事故。

When repairing the induction automatic door, it is necessary to first turn off the power supply of the door to avoid electric shock accidents.

2.在更換感應器或者控制器時，需要選擇與原設備相同的型號和規格，以免影響門的正常使用。

When replacing sensors or controllers, it is necessary to choose the same model and specifications as the original equipment to avoid affecting the normal use of the door.

3.在調整門扇位置或者螺絲時，需要使用工具，以免損壞門扇或者門框。

When adjusting the position or screws of the door leaf, it is necessary to use professional tools to avoid damaging the door leaf or frame.

總之，感應自動門的維修需要技術和經驗，如果遇到故障需要及時聯系維修人員進行處理。希望本文能夠幫助大家更好地了解感應自動門的維修方法，保障門的正常使用。更多事項就來我們網站http://www.lebimv.cn咨詢！

In short, the maintenance of the induction automatic door requires professional technology and experience. If there is a malfunction, it is necessary to promptly contact professional maintenance personnel for handling. I hope this article can help everyone better understand the maintenance methods of induction automatic doors and ensure their normal use. For more information, come to our website http://www.lebimv.cn consulting service